You're viewing a previously published revision of this guide.  View latest revision

Older
Jan 10, 2014 - 07:01:08
Jan 17, 2014 - 07:01:05 Jan 10, 2014 - 07:01:06 Jan 10, 2014 - 07:01:16 Jan 10, 2014 - 07:01:08 Jan 10, 2014 - 07:01:29 Jan 03, 2014 - 01:01:35 Jan 03, 2014 - 07:01:31 Aug 01, 2013 - 11:08:04 Jul 15, 2013 - 08:07:06 Jul 11, 2013 - 11:07:12 Jul 11, 2013 - 11:07:54 Jul 11, 2013 - 09:07:49 Jul 11, 2013 - 09:07:57 Jul 11, 2013 - 09:07:55 Jul 11, 2013 - 08:07:20 Jul 11, 2013 - 06:07:09 Jul 11, 2013 - 06:07:28 Jul 11, 2013 - 06:07:33 Jul 11, 2013 - 06:07:32 Jul 11, 2013 - 06:07:28 Jul 11, 2013 - 05:07:39 Jul 11, 2013 - 05:07:22 Jul 11, 2013 - 05:07:15 Jul 11, 2013 - 05:07:51 Jul 11, 2013 - 05:07:03 Jul 01, 2013 - 01:07:41 Jul 01, 2013 - 01:07:37 Jul 01, 2013 - 01:07:18 Jul 01, 2013 - 01:07:53 Jul 01, 2013 - 01:07:49 Jul 01, 2013 - 01:07:33 Jul 01, 2013 - 01:07:15 Jul 01, 2013 - 01:07:08 Jul 01, 2013 - 01:07:46 Jul 01, 2013 - 01:07:28 Jul 01, 2013 - 01:07:04 Jul 01, 2013 - 11:07:53 Jul 01, 2013 - 06:07:17 Jul 01, 2013 - 06:07:04 Jul 01, 2013 - 06:07:54 Jul 01, 2013 - 06:07:36 Jul 01, 2013 - 06:07:25 Jul 01, 2013 - 06:07:55 Jun 28, 2013 - 01:06:15 Jun 28, 2013 - 01:06:56 Jun 28, 2013 - 01:06:05 Jun 28, 2013 - 01:06:59 Jun 28, 2013 - 01:06:28 Jun 28, 2013 - 01:06:52 Jun 28, 2013 - 11:06:23 Jun 28, 2013 - 11:06:02 Jun 28, 2013 - 11:06:14 Jun 28, 2013 - 06:06:44 Jun 28, 2013 - 06:06:34 Jun 27, 2013 - 12:06:28 Jun 27, 2013 - 11:06:59 Jun 27, 2013 - 11:06:20 Jun 27, 2013 - 11:06:40 Jun 27, 2013 - 11:06:57 Jun 27, 2013 - 11:06:30 Jun 27, 2013 - 11:06:39 Jun 27, 2013 - 11:06:45 Jun 27, 2013 - 11:06:57 Jun 27, 2013 - 11:06:57 Jun 27, 2013 - 11:06:54 Jun 20, 2013 - 10:06:05 Jun 12, 2013 - 12:06:25 Jun 12, 2013 - 12:06:22 Jun 12, 2013 - 12:06:18
Newer

How to Repair a KMT Style SL4 Static Seal Assembly Using Kit #12136

Written By: Adam Dumas (and one other contributor)
  • Comments: 0
  • Favorites: 0
  • Completions: 1

Difficulty

Moderate

Steps

3

Time Required

00:10:00 - 00:20:00

Sections

1

Flags

0

Introduction

Hypertherm is in no way affiliated with the above mentioned manufacturer.

  1. Remove all the components from the static end of the high-pressure cylinder with the proper tools. Clean all Blue Goop off the high-pressure cylinder with isopropyl alcohol or a similar cleaning agent. Apply high vacuum grease to the O-ring.

  2. Slide o-ring onto groove of HP seal Insert HP seal into end of HP cylinder Insert static back-up behind the HP seal

    • Slide o-ring onto groove of HP seal

    • Insert HP seal into end of HP cylinder

    • Insert static back-up behind the HP seal

  3. Apply blue goop to both ends of HP cylinder threads

    • Apply blue goop to both ends of HP cylinder threads

    • Reassemble HP cylinder into intensifier assembly

Author

with 1 other contributor

Adam Dumas

Member since: 05/20/2013

36 Guides authored